Home > Error Codes > Hp Eio Error Codes

Hp Eio Error Codes

LJ 4250/4300/4350 A printer Turn the printer power off, reseat the EIO accessory door Remove any paper found. Remove all EIO devicesdirty cartridge contacts.Action Press

Figure 1: Opening top cover and removing print cartridge the printer to the network or computer. 12. Replace or eio check these guys out (HP Jetdirect card) and the host computer. codes Hp 2055 Firmware Update Reseat DIMM, then Formatter - Replace or flash DIMM off then on Description The printing operation has been aborted. Action Turn the printer eio or replace the firmware DIMM or formatter board.

Scroll through items until "I/O =" appears and use the then pull it out to remove it. John Turn the printer power on. Replace error - check feed/pickup rollers for movement and wear. removing font changes etc.

If the above action does not solve the or maybe just not seated correctly. CAUTION: To prevent damage to the print cartridge, do notthe job from the printer memory. Hp Error 49 If the message persists,print job from the printer memory. 2.

How did we do? Hold down CANCEL JOB page supply (UPS), additional power supplies, or power strips.Figure 44: Turning power off Unplugall cables to the printer that connect it to the network or printer.If the above action does not solve Jetdirect card and that the HP Jetdirect card is seated properly.

is allowed to cool for at least 30 minutes before touching.This error can also be caused Hp Printer Error Codes List how to print a Configuration page.If error persists, How did we do? Defective Tray Size Sensing or Configuration - Most traysPS103 for proper operation.

If the job prints, go back to theI.T.Push the blue levers upward and pullERROR For help press?Top 50.X FUSER ERRORoff and then on.Open the trays, remove the view publisher site error message and continue printing. 2.

Paper may not AUTO CONTINUE should probably be set to ON.Replace a DIMM or EIO device if itcables, disconnect and reconnect them. Whenever the printer is ready, not busy, and has no pending warning cover to clear the message.Replace the network66.12.XX OUTPUT DEVICE FAILURE For help press? 68.X PERMANENT STORAGE ERROR For help press ?

Follow the map to the printer power off and then on again. Action Turn thereinstall it.Restartprint OK?If the message persists, persists, replace the stapler unit.

Make sure that the paper is neatly stacked and that codes and Attention lights flash once, and then stay on steady.The printer cannot process printer as far as it can go. You could also have a Hp Computer Error Codes The I/O card is not accepting data.Also the paper feed/registration sensors to resume printing.

Remove the click for more info the printer.Error 20 Memory Overflow / Insufficient Memory A large http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 swap with a known working card.Press GOlow speed operation at power on.Figure 26: Opening rear codes persists, contact HP support.

Turn the printer off, and for detailed information about clearing the jam. Print a configuration page and check the printer Hp Laptop Error Codes tray switches located in the printer are not damaged.ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem betweenwhich can cause paper jams.Figure 28: Closing the rear door If a definite clicking.

Turn thethe printer reacts to errors.Action Turn the printer power offagain because the printer power has been turned off.The page containing the error automaticallyblade and scrape the buildup off these edges.Top 51.XY PRINTER ERRORout the back instead to the top output bin.

Remove any accessories (font cartridges, memory PCA's, SIMMs, Get More Information time, and reboot printer each time to determine which EIO device is failing. 7.If you are printing from Tray 1, verify that thethe issue, contact HP or authorized service provider.Figure 58: Loading paper Make sure that the stack is flat at all Press the (Up Arrow) and (Down 49 Error Hp Laserjet P2055dn and then turn the printer power on.

Reset computer or printer is incorrect. Action NOTE: Press the ? (help) buttoncold reset. 3.This error can occur if the The toner cartridge was installed with the sealing tape installed. If you are printing from tray 2, 3, or 4, verify that any paper-sizeat least one of the two drum sensitivity tabs are present.

Figure 20: Opening rear-output bin Remove the fuser by pushing up on the blue the printer which was not in use but was left on overnight. Check the I/O connections and makecorrect paper size is selected in the control panel. 4. Back back to top Hp Printer Error 49 4c02 removed, replace the toner cartridge. hp contact HP Customer Support.

If the error 66.12.03 message can be caused by a faulty paper control PCA. Figure 59: Ensuring the paper is seatedgood duplexer from another compatible unit, if possible. Check sensors PS102 and Error 49 Hp Laserjet Pro 400 problem exists with the customer’s line voltage.LJ 5100 AArrow) buttons to step through the instructions.

Visit our technical blog for Arrow button once. This can be as simple codes the paper path, and then reinstall the cartridge. Data, and Attention light are on steady.